Panels (factory) : Louvered (Full Unit) Enc. Switch :ASME Pressure Vessel and Associated Codes :Remote CoolerĬONDENSER FIELD X C B P H: Aluminum : Copper : Black Fin : Phenolic : Heat Recovery X : TEAO Fan MotorsĤ8 49 50 51 52 53 54CABINET FIELD 1 3 5 7 P B D L H 1 S N: Wire (Full Unit) Enc. FIELD X 3 D W V S D A R :150# PSI DWP :300# PSI DWP :Double Thick Insulation :Weld Flange :Victaulic Flange :Flow Switch :Diff. : : Pump Control : OptiView Remote Panel S : Sequence Control & Automatic Lead Transferģ8 39 40 41 42 43 44EVAP.
YORK YCAL HIGH AMBIENT KIT CODE
American Safety Code (cU.L./cETL) : No Listing (typically 50 HZ non-CE, non-U.L. and Current Reset / Offset B : ISN Microgateway : Spanish LCD & Keypad Display : French LCD & Keypad Display : German LCD & Keypad Display : Italian LCD & Keypad Display : Portuguese LCD & Keypad Display : Silent Night : N. Reset / Offset C : Current Reset / Offset S : Temp. Handles = Individual System Breaker & Lockable External Handle
MP = Multiple Point SP = Single Point NF = Non-Fused TB = Terminal Block Ser. Brine (LBrT) : Thermal Storage : Chicago Relief Code : Service Isolation Valve : Both Chicago Relief Code & Isolation Valve : : : : : : Control Transformer O : Convenience OutletĢ0 21 22 23 24 25 26 27 28CONTROLS FIELD X T C B M S F G I P N L N Q OĢ9 30 31 32 33 34 35 36 37COMPRESSOR / PIPING FIELD: Low Temp. PART NUMBER LETTER CODES16 17 18 19POWER FIELD S B S C X X S S: SP TB : SP CB : SP TB w/ Ind. UNIT NOMENCLATURE NAMEPLATE ENGINEERING DATABASIC PART NUMBER 49 TRANSDUCER AND THERMISTOR WIRE HARNESS CONNECTORS. 40 PLUG AND JUMPER ARRANGEMENT.41 SENSOR HARNESSES. 38 VARIABLE SPEED DRIVE FAN ASSEMBLY COMPONENTS. 26 VARIABLE SPEED DRIVE CONTROL AND VARIABLE SPEED DRIVE PANEL CONFIGURATION.28 VARIABLE SPEED DRIVE PANEL COMPONENTS.30 VARIABLE SPEED DRIVE POWER ASSEMBLY COMPONENTS. 14 PIPING REFRIGERANT PIPING COMPONENTS.16 GLYCOL LOOP COMPONENTS. 6 CONDENSER COILS CONDENSER COIL COMPONENTS. UNIT NOMENCLATURE NAMEPLATE ENGINEERING DATA. Voltages as low as 50 volts may cause death. LOW VOLTAGEDO NOT be misled by the term low voltage.
Be careful not to contact high voltage connections when installing or operating this equipment. When working inside equipment with power off, take care to discharge every capacitor likely to hold dangerous potential. Shut off power supply to the equipment before beginning work and follow lockout procedures. DEATH OR SERIOUS INJURY may result if personnel fail to observe safety precautions.Work on electronic equipment should not be undertaken unless the individual(s) have been trained in the proper maintenance of equipment and is (are) familiar with its potential hazards. HIGH VOLTAGE Is used in the operation of this equipment. If there is any question in the mind of operating/ service personnel as to the applicability of these documents, then, prior to working on the equipment, they should verify with the owner, whether the equipment has been modied and if the current literature is available. It is the responsibility of operating/service personnel as to the applicability of these documents to the equipment in question.
YORK YCAL HIGH AMBIENT KIT UPDATE
While YORK makes no commitment to update or provide current information automatically to the manual user, that information, if applicable, can be obtained by contacting the nearest YORK Engineered Systems Service ofce. MODELS YCAV0569, 0639, 0679, 0719, 0739, 0819, 0889 and YCAV0969 STYLE "A"ĬHANGEABILITY OF THIS DOCUMENTIn complying with YORK's policy for continuous improvement, the information contained in this document is subjected to change without notice. AIR-COOLED SCREW LIQUID CHILLERSRENEWAL PARTSNew Release Form: 201.21-RP2 (605)